Ceiling and floor scanning identified reinforcement, possible conduit and a congested no-drill zone before hood anchoring and sawcutting.

GPR identified changes in subgrade response beneath slab areas experiencing recurring water intrusion.

Patio scanning documented slab reinforcement, perimeter footing conditions and the connection to the original patio.

Six warehouse locations were scanned to verify slab thickness and reinforcement consistency across the facility.

Proposed trench cuts were scanned to identify reinforcement and footing locations before sawcutting.

A 15-inch-thick slab was scanned to identify shallow wire mesh and structural reinforcement before electrical trenching.

Two renovation sawcut areas were scanned to locate post-tension cables before concrete cutting.

Twelve garage anchor locations were scanned to locate post-tension cables before car-lift installation.

Garage lift-anchor locations were scanned to locate post-tension cables before installation.

A 160-foot sawcut route was scanned to map reinforcement before plumbing work within an orthodontic-office build-out.

Bathroom slab scanning identified post-tension cables and a grade beam before renovation work.

Kitchen and bathroom trench areas were scanned to locate post-tension cables and grade beams before renovation cutting.

Bollard locations were evaluated across waterproofed and structural parking areas to determine where reliable anchor scanning was possible.

A 100-foot sawcut route was scanned to identify reinforcement, footings and grade beams before power and data installation.

Multi-phase scanning supported plumbing layout revisions and overhead mechanical installation within both post-tensioned and slab-on-grade areas.

Kitchen, bathroom and garage areas were scanned to locate post-tension cables before plumbing, electrical and concrete modifications.

Anchor areas were scanned to locate post-tension cables, reinforcement and highly congested structural zones before drilling.

Five ceiling locations were scanned before through-slab drain penetrations were drilled in an existing hotel.

Targeted slab scanning documented reinforcement and subsurface findings before an existing sewer line was accessed for repair.

Floor-anchor locations were scanned to identify slab reinforcement before equipment racks were secured.

A 300-foot trench route was scanned to identify rebar, grade beams, footings and congested structural areas before cutting.

Utility-trench scanning documented reinforcement, footing edges and deeper footing cages before sawcutting.

Slab scanning documented post-tension cables, slab thickness and beam transitions before new structural footing pads were installed.

Slab scanning documented reinforcement and footing conditions before a former medical office was converted into a bank

Ten plumbing locations were scanned to document two layers of reinforcement and concealed conduit before coring.

Wall and floor scanning documented reinforcement, changing concrete thickness and areas requiring additional verification before drilling.

Twenty-nine plumbing locations were scanned to identify reinforcement, conduit, joists and beams before drilling.

Targeted scanning documented wire mesh and added reinforcement before plumbing and electrical penetrations were drilled.

Overhead scanning located post-tension cables and reinforcement before lighting, HVAC and ceiling anchors were drilled.

Initial scanning identified banded post-tension cables that required the restroom layout and several proposed core locations to be revised.

Plumbing-trench scanning identified changing slab conditions, post-tension cables and structural areas requiring additional cutting precautions.

Targeted scanning documented reinforcement and footing transitions to support a planned garage remodel and addition.

A 74-foot plumbing trench was scanned to locate reinforcement before concrete cutting.

The kitchen slab was scanned to locate post-tension cables and slab thickening before plumbing relocation.

Fitness equipment anchor locations were scanned to identify post-tension cables before drilling.

A proposed bathroom plumbing route was scanned to locate post-tension cables before renovation work began.

Two proposed electrical sawcut areas were scanned to identify reinforcement and determine appropriate cutting precautions.

Approximately 300 linear feet of plumbing trench was scanned to locate reinforcement and conduit before concrete cutting.

Three phased scanning visits supported revised plumbing and electrical core locations within a congested post-tensioned slab.

Targeted scanning documented slab thickness, reinforcement and footing conditions across newer and older warehouse areas.

Scanning identified reinforcement that did not match the specified layout, allowing the panels to be replaced before installation.

Preconstruction scanning identified congested areas and guided layout revisions before drilling and installation.